產品介紹：

　　Product Introduction

　　干粉抹面砂漿是將水泥、填料、骨料和多種功能性外加劑配制而成。對建筑物和墻體可起保護作用。它可以抵抗風、雨、雪等自然環境對建筑物的侵蝕，并提高建筑物的耐久性產品性能：

　　Dry powder plastering mortar is a mixture of cement, filler, aggregate, and various functional additives. It can provide protection for buildings and walls. It can resist the erosion of natural environments such as wind, rain, and snow on buildings, and improve the durability and product performance of buildings

　　1.良好的和易性

　　1. Good workability

　　2.粘結力強

　　2. Strong adhesion

　　3.牢固性強、耐久性強、耐氣候影響施工工藝：

　　3. Strong firmness, durability, and weather resistance construction technology:

　　1清除墻面的灰塵、污垢、堿膜、砂漿塊等附著物，要灑水潤濕。對主體結構梁、柱有凸出部位先進行鑿出，并確保砂漿厚度，如有個別地厚度較薄處可加設玻璃纖維網格。

　　1. Clean the wall of dust, dirt, alkali film, mortar blocks and other attachments, and sprinkle water to wet them. Chisel out the protruding parts of the main structural beams and columns first, and ensure the thickness of the mortar. If there are individual areas with thinner thickness, glass fiber mesh can be added.

　　2.吊直，做灰餅。抹底層灰前必須先橫線找平，立線吊直，彈出基準線和墻裙、踢腳板線。先用托線板檢查墻面平整、垂直程度，并在控制陽角正的情況下大致確定抹灰厚度后(最薄處一般不小于7mm)，掛線做灰餅(灰餅厚度應不包括面層)。在地面上彈出十字線作為基準線，并結合墻面平整、垂直程度大致確定墻面抹灰厚度，并吊線“做灰餅”，“做灰餅”時應先在左右墻角上各做一個標準餅，然后用線錘吊垂直線做墻下角兩個標準餅(高低位置一般在踢腳線上口)，再在墻角左右兩個標準餅面之間通線，每隔1.2m~1.5m左右及在門窗口陽角等處上下各補做若干個灰餅。

　　2. Hang straight and make gray cakes. Before applying the bottom layer of plaster, it is necessary to level the horizontal line, hang the vertical line straight, and mark the reference line, wall skirt, and skirting board line. First, use a wire support board to check the flatness and verticality of the wall surface, and roughly determine the plastering thickness (generally not less than 7mm at the thinnest point) while controlling the positive angle. Then, hang a line to make a plaster cake (the plaster cake thickness should not include the surface layer). Pop a cross line on the ground as a reference line, and roughly determine the thickness of the wall plastering based on the flatness and verticality of the wall. Hang a line to make a "plaster cake". When making a plaster cake, first make a standard cake on each corner of the wall, and then use a plumb bob to hang a vertical line to make two standard cakes at the bottom corner of the wall (usually at the top of the skirting board). Then, make a line between the two standard cake surfaces on the left and right corners of the wall, and add several plaster cakes every 1.2m~1.5m and at the corners of doors and windows.

　　3.墻面沖筋：待灰餅結硬后，使用與抹灰層相同的砂漿，在上下灰餅之間做寬約30~50mm的灰漿帶，并以上下灰餅為準用壓尺推平。沖筋完成后應待其稍干后才能進行墻面底層抹灰作業。

　　3. Wall reinforcement: After the plaster cake has hardened, use the same mortar as the plastering layer to create a mortar strip with a width of about 30-50mm between the upper and lower plaster cakes, and use a pressure ruler to flatten the upper and lower plaster cakes. After the reinforcement is completed, it should be allowed to dry slightly before carrying out the plastering work on the bottom layer of the wall.

　　4.做護角：根據砂漿墩和門框邊離墻面的空隙，用尺規后，分別在陽角兩邊吊直和固定好靠尺板，抹出水泥砂漿護角，并用陰角抹子推出小圓角，最后利用靠尺板，在陽角兩邊50mm以外位置，以40度斜角將多余砂漿切除、清凈。

　　4. Make corner protectors: According to the gap between the mortar pier and the door frame edge and the wall surface, use a ruler to hang and fix the guiding board on both sides of the external corner, apply cement mortar corner protectors, and use a corner scraper to push out small corners. Finally, use the guiding board to cut off and clean the excess mortar at a 40 degree angle 50mm away from both sides of the external corner.

　　5.抹底層灰和中層灰：在墻體濕潤的情況下抹底層灰，對混凝土墻體表面宜先刷水泥漿一遍，并在不同材質結合處掛鋼絲網，與不同材質的接觸面不低于30cm,隨刷隨抹底層灰。分層抹面，若抹灰層局部厚度超限(一般在20～35mm之間)，則應在抹灰層之間加設鋼絲網片。 鋼絲網固定式：采用2.5×28mm鍍鋅水泥釘固定， 鋼絲網掛設在固定時鋼絲網須攤平拉緊。固定鋼絲網邊緣時，水泥釘宜布置在離鋼絲網邊線2～3cm處，以便壓緊鋼絲網，不使其邊緣翹曲。鋼絲網片與抹灰基層搭接不小于100mm，鋼絲網片之間搭接亦不小于100mm。水泥釘間距不大于300mm。

　　5. Apply bottom and middle layer plaster: Apply bottom layer plaster when the wall is wet. It is recommended to brush the surface of the concrete wall with cement slurry first, and hang steel wire mesh at the joint of different materials. The contact surface with different materials should not be less than 30cm, and apply bottom layer plaster as needed. Layered plastering, if the local thickness of the plastering layer exceeds the limit (generally between 20-35mm), steel wire mesh should be added between the plastering layers. Fixed steel wire mesh: fixed with 2.5 × 28mm galvanized cement nails. When the steel wire mesh is hung and fixed, it must be flattened and tightened. When fixing the edge of the steel wire mesh, cement nails should be placed 2-3cm away from the edge of the steel wire mesh to compress it and prevent the edge from warping. The overlap between the steel wire mesh and the plaster base shall not be less than 100mm, and the overlap between the steel wire mesh shall not be less than 100mm. The spacing between cement nails shall not exceed 300mm.

　　本文由  濟南抹面砂漿 友情奉獻.更多有關的知識請點擊  http://m.man5g.cn/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Jinan plaster mortar For more related knowledge, please click http://m.man5g.cn/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.